Audi A4, S4

since 2000 release

Repair and operation of the car



Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water-collecting compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and installation/adjustment of a cowl
      Removal and installation of a cable of the drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and installation of a door
      Adjustment of a door
      Removal and installation of a frame of a window of a forward door
      Removal and installation of a window regulator
      Removal and installation of the electric motor of the drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and adjustment of a trunk lid
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Station wagon)
      Removal and installation of a door of a back (Station wagon)
      Removal and installation of the lock of a door of a back (Station wagon)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of screenwash
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + Equipment of salon
+ Onboard electric equipment






Check and adjustment of a starting position of the movable panel of a roof

Installation of the electric motor of the movable panel in a starting position

 PERFORMANCE ORDER

  1. Close the movable panel.
  2. Remove a forward ceiling plafond, address to the Section Removal and installation of plafonds of internal lighting.
  3. Unscrew screws of fastening and remove the electric motor of the movable panel.
  4. Do not disconnect electric wires of the electric motor.
  5. Include ignition.
  6. Establish by the rotary switch the situation "The Roof Is Closed". Thus the electric motor works automatically and stops in zero situation.
  7. In this situation install the electric motor at the closed roof and fix it.
  8. Establish a forward plafond.

Check of a starting position of the kulisny directing

 PERFORMANCE ORDER

The starting position can be checked by means of a pocket mirror and a pocket lamp at the installed movable panel.

  1. Remove lateral slips at the left and on the right, address to appropriate section.
  1. Open and again close the movable panel.
  1. Shift the ceiling panel completely back.
  1. Put a pocket mirror on the movable panel and check a starting position. At the correct installation a rectangular groove in the mechanism of promotion kulisny directing (1) has to coincide with a groove (an arrow on an accompanying illustration). Otherwise make adjustment.

Installation of the directing coulisse in a starting position

 PERFORMANCE ORDER

  1. Remove the movable panel.
  2. Remove the panel electric motor.
  3. Remove lateral slips, address to appropriate section.
  4. Displace kulisny directing (1) from both parties from back situation forward.
  5. Install a rectangular groove in the mechanism of promotion kulisny directing (1) so that it coincided with a groove (shooter) on the directing tire (2) panels of a ceiling. Thus the starting position of the directing coulisse is established.
  6. Install the electric motor of the movable panel in a starting position.
  7. Establish lateral slips.