Audi A4, S4

since 2000 release

Repair and operation of the car



Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water-collecting compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and installation/adjustment of a cowl
      Removal and installation of a cable of the drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and installation of a door
      Adjustment of a door
      Removal and installation of a frame of a window of a forward door
      Removal and installation of a window regulator
      Removal and installation of the electric motor of the drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and adjustment of a trunk lid
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Station wagon)
      Removal and installation of a door of a back (Station wagon)
      Removal and installation of the lock of a door of a back (Station wagon)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of screenwash
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + Equipment of salon
+ Onboard electric equipment






External equipment

Installation of the forward panel in situation for maintenance

1 — the Forward panel
2 — the Top cover of the engine, left
3 — the Top cover of the engine, right
4 — the Screw, 10nm
5 — the Screw, 50nm

3369 — the Provision of service: Screw the special AUDI tool in openings in a bumper. Instruction: If the specified special tool available is not present, it is possible to use 2 M8 x 90 screws. Under a head of a bolt it is necessary to enclose washers with a diameter of 24 mm and 2 mm thick. Besides, 2 plugs 80 mm long and with a diameter of 17 mm are necessary.

When carrying out some adjusting works, for example, with a maple or gear belt the forward panel has to be installed in situation for an obsluzhivniya. Thus the panel is displaced together with a radiator forward.

 PERFORMANCE ORDER

  1. Disconnect air ducts (1) and (2) between the forward panel and the air filter on the forward panel (shooters on sopr. illustrations).
  1. Remove the top cover of the engine (2) and on the right (3) at the left, address to an illustration at the beginning of the section.
  2. Disconnect the lower cover of the engine ahead, without removing it. For this purpose unscrew only 3 screws.
  3. Remove a front bumper, address to appropriate section.
  1. Screw in two top openings on the right and at the left the special tool 3369.
  1. Turn out screws (5) at the left and on the right, address to an illustration at the beginning of the section.
  2. Turn out screws (4) at the left and on the right.
  1. Pull the forward panel forward so that the back opening on the panel was closed by a forward carving opening on a wing. In this situation screw at the left and on the right a bolt (the shooter on an accompanying illustration) and fix the panel.