Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
General information and security measures when carrying out body works
Cleaning and leaving
Repair of insignificant damages of body panels
Repair of considerable damages of a body
- External equipment
Installation of the forward panel in situation for maintenance
Removal and installation of a cover of a water-collecting compartment
Removal and installation of a front bumper
Removal and installation of a loker of a back wing
Removal and installation of a loker of a forward wing
Removal and installation of a forward wing
Removal and installation of a rear bumper
Removal and installation/adjustment of a cowl
Removal and installation of a cable of the drive of a cowl
Removal and installation of a clamp of the lock
Removal and installation of facing of a forward door
Removal and installation of facing of a back door
Removal and installation of a door
Adjustment of a door
Removal and installation of a frame of a window of a forward door
Removal and installation of a window regulator
Removal and installation of the electric motor of the drive of a window regulator
Removal and installation of the lock of a door
Removal and installation of the handle of a door
Removal and installation of the cylinder of the lock of a door
Removal and installation of facing of a trunk lid
Removal, installation and adjustment of a trunk lid
Removal and installation of the lock of a luggage carrier
Removal and installation of facing of a door of a back (Station wagon)
Removal and installation of a door of a back (Station wagon)
Removal and installation of the lock of a door of a back (Station wagon)
Removal and installation of an external mirror
Removal and installation of moldings
Removal, installation and check of the movable panel of a roof
Removal and installation of an overlay of the movable panel of a roof
Check and adjustment of a starting position of the movable panel of a roof
Removal and installation of a sealant of the movable panel
Replacement of elastic bands of brushes of a screen wiper
Removal and installation of a jet of windscreen washer of a windshield
Removal and installation of a jet of a washer of back glass
Removal and installation of the lever of screenwash
Removal and installation of the lever of a cleaner of back glass
Removal and installation of jets of a faroomyvatel
Adjustment of levers of a screen wiper
+ Equipment of salon
+ Onboard electric equipment
|
Removal and installation of facing of a back door Facing of a door
Removal
|
|
- Disconnect a negative cable (-) of the battery.
- Disconnect from facing a decorative level (2) and remove it forward.
- Turn out 4 screws (3).
- Manual window regulator: Remove the handle of a window regulator (5).
- Enter a plastic wedge around clips between the panel of a door and facing and remove facing from a door.
- Take away facing from a frame of a door a little and disconnect a door drive cable, address to the Section Removal and installation of facing of a forward door.
- Disunite the socket of the switch of a window regulator (9).
- Remove facing from a door frame.
|
|
Installation
|
|
- Before installation check correctness of provision of tightening nuts (8) and razzhimny nuts (7) on a door frame.
- Installation is carried out in sequence, the return to removal. Thus pay attention that the hook (3) drafts shows upward.
- Manual window regulator: Install into place the window regulator handle.
- Attach a negative cable (-) of the battery.
|
|
Window regulator handle
Removal
|
|
- Enter a screw-driver between a cover (4) and the handle of a window regulator.
- Uncover the window regulator handle.
- Turn out the screw (6) and remove the handle.
|
|
Installation
|
|
- Install the window regulator handle in the situation "for 6 hours" (± 15 °) at the closed window on a handle axis.
|
|
|
|