Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
General information and security measures when carrying out body works
Cleaning and leaving
Repair of insignificant damages of body panels
Repair of considerable damages of a body
- External equipment
Installation of the forward panel in situation for maintenance
Removal and installation of a cover of a water-collecting compartment
Removal and installation of a front bumper
Removal and installation of a loker of a back wing
Removal and installation of a loker of a forward wing
Removal and installation of a forward wing
Removal and installation of a rear bumper
Removal and installation/adjustment of a cowl
Removal and installation of a cable of the drive of a cowl
Removal and installation of a clamp of the lock
Removal and installation of facing of a forward door
Removal and installation of facing of a back door
Removal and installation of a door
Adjustment of a door
Removal and installation of a frame of a window of a forward door
Removal and installation of a window regulator
Removal and installation of the electric motor of the drive of a window regulator
Removal and installation of the lock of a door
Removal and installation of the handle of a door
Removal and installation of the cylinder of the lock of a door
Removal and installation of facing of a trunk lid
Removal, installation and adjustment of a trunk lid
Removal and installation of the lock of a luggage carrier
Removal and installation of facing of a door of a back (Station wagon)
Removal and installation of a door of a back (Station wagon)
Removal and installation of the lock of a door of a back (Station wagon)
Removal and installation of an external mirror
Removal and installation of moldings
Removal, installation and check of the movable panel of a roof
Removal and installation of an overlay of the movable panel of a roof
Check and adjustment of a starting position of the movable panel of a roof
Removal and installation of a sealant of the movable panel
Replacement of elastic bands of brushes of a screen wiper
Removal and installation of a jet of windscreen washer of a windshield
Removal and installation of a jet of a washer of back glass
Removal and installation of the lever of screenwash
Removal and installation of the lever of a cleaner of back glass
Removal and installation of jets of a faroomyvatel
Adjustment of levers of a screen wiper
+ Equipment of salon
+ Onboard electric equipment
|
Removal, installation and adjustment of a trunk lid Sedan
Removal
|
|
- Disconnect a negative cable (-) of the battery.
|
|
|
- Remove facing of a trunk lid, address to the Section Removal and installation of facing of a trunk lid.
- Disunite sockets and take out from a trunk lid.
|
|
|
For simplification of installation it is necessary to fix a cord which after a pulling of wires remains in a cover on the ends of a wire. |
|
- For repeated installation: Mark with a felt-tip pen position of balance weights of loops (3) on a trunk lid.
|
|
- Remove a gas-filled emphasis, address to the Section Removal and installation of a door of a back (Station wagon).
- Ask the assistant to take a trunk lid and turn off on 2 nuts of fastening (1) and (2) at the left and on the right in a trunk lid.
- Remove a trunk lid by means of the assistant.
|
|
Installation
|
|
- Establish a trunk lid by means of the assistant into place. Expose an old cover on earlier put tags.
- Screw on two nuts at the left and on the right.
- Establish a gas-filled emphasis, address to the Section Removal and installation of a door of a back (Station wagon).
- Release maple the lock, close a trunk lid and adjust its situation so that the gap on a contour of a prileganiye was uniform, address to appropriate section.
- Tighten a nut the moment 21nm.
- Further installation is carried out in sequence, the return to removal.
- Attach a negative cable (-) of the battery.
|
|
Check and adjustment
|
|
- Check trunk lid gaps. The gap on a contour of a prileganiye has to be uniform.
|
|
- Remove facing of overlapping of a back, address to the Section Removal and installation of facings (Sedan).
|
- Weaken nuts (1) so that it was possible to displace maple the lock (2).
|
|
- Close a trunk lid and adjust a gap on a prileganiye contour.
- Open a trunk lid and tighten nuts of fastening of the maple lock the moment 8nm.
- Establish into place facing of overlapping of a back, address to the Section Removal and installation of facings (Sedan).
|
- Remove rubber covers (2) on an emphasis at the left and on the right and screw an emphasis (1) completely in a trunk lid.
|
|
- Screw an emphasis so that the closed cover (3) was aflush with adjacent elements of a body, and an emphasis slightly adjoined to a cargo edge (4).
- Put on rubber covers an emphasis.
|
|
|
|