Audi A4, S4

since 2000 release

Repair and operation of the car


Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water-collecting compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and installation/adjustment of a cowl
      Removal and installation of a cable of the drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and installation of a door
      Adjustment of a door
      Removal and installation of a frame of a window of a forward door
      Removal and installation of a window regulator
      Removal and installation of the electric motor of the drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and adjustment of a trunk lid
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Station wagon)
      Removal and installation of a door of a back (Station wagon)
      Removal and installation of the lock of a door of a back (Station wagon)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of screenwash
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + Equipment of salon
+ Onboard electric equipment





Removal and installation of the lever of screenwash

Removal

 PERFORMANCE ORDER

  1. Moisten a windshield with water.
  1. Include quickly a screen wiper and switch off it the switch. Thus the screen wiper stops in extreme situation.
  1. Note on glass the provision of brushes at correctly installed levers, for example, by means of an adhesive tape.
  1. Open a cowl.
  1. Hook a screw-driver and uncover (3), (1) – brackets; (5) – spoiler lattice.
  1. Turn off a nut (4) approximately on 2 turns, without turning off it completely. Slightly move the lever (2) so that it separated from an axis. Turn off a nut completely and remove the lever from an axis. HAZET 1966-05 can apply also special stripper to this purpose, for example.

If the lever hard is removed, hook it a wrench and carefully remove.

Installation

 PERFORMANCE ORDER

  1. Check that the electric motor of a screen wiper stood in extreme situation. If necessary, quickly turn on the electric motor and switch off the switch.
  1. Install the lever on an axis of a screen wiper and expose it by means of the tag put in the form of an adhesive tape. It is also possible to expose the lever on distance between a brush and a lattice of a spoiler, having measured it from the right top of a cleaner

    Sedan/versatile person
    and = 26 mm
    b = 45 mm
    Cabriolet:
    and =24 ± 5 mm
    b = 35 ± 5 mm

  1. Screw a nut and tighten it by hand.
  1. Check extreme position of levers. For this purpose close a cowl, moisten glass with water and quickly include a screen wiper. Screen wipers have to return to the adjusted extreme situation and should not go out of the edge of glass. If necessary, turn off nuts and again adjust the provision of screen wipers.
  1. Tighten nuts the moment 21nm. Establish to the place of a cover of levers.