Audi A4, S4

since 2000 release

Repair and operation of the car


Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water-collecting compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and installation/adjustment of a cowl
      Removal and installation of a cable of the drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and installation of a door
      Adjustment of a door
      Removal and installation of a frame of a window of a forward door
      Removal and installation of a window regulator
      Removal and installation of the electric motor of the drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and adjustment of a trunk lid
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Station wagon)
      Removal and installation of a door of a back (Station wagon)
      Removal and installation of the lock of a door of a back (Station wagon)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of screenwash
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + Equipment of salon
+ Onboard electric equipment





Removal and installation of the lock of a door of a back (Station wagon)

Back door lock

Removal

 PERFORMANCE ORDER

  1. Open a door and remove facing, address to appropriate section.
  1. Squeeze out a clip (5) and disconnect a cable from the lock.
  1. Incline the plug (7) to the right and disconnect a driving bar (1).
  1. Turn out 2 nuts (2) and (4) and remove the lock (3) from a back door.

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence, the return to removal. Thus tighten nuts the moment 21nm.

Back door: Electric motor of the uniform lock

Removal

 PERFORMANCE ORDER

  1. Disconnect a negative cable (-) of the battery.

Observe indications of the Section Replacement of the Battery.

  1. Open a door of a back and remove facing of a door, address to the Section Removal and installation of facing of a door of a back (Station wagon).
  1. Disconnect a driving bar (3) at the hinged plug (4).
  1. Disconnect a driving bar (3) at the electric motor (1) (shooter).
  1. Weaken 3 screws of fastening of the electric motor (2) and remove the electric motor.
  1. Disunite the electric motor socket.

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence, the return to removal.
  2. Attach a negative cable (-) of the battery.

Observe indications of the Section Replacement of the Battery.