Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
General information and security measures when carrying out body works
Cleaning and leaving
Repair of insignificant damages of body panels
Repair of considerable damages of a body
+ External equipment
- Equipment of salon
Remarks on work with the equipment of salon and a security measure
Removal and installation of spring clips
Removal and installation of the central console
Removal and installation of the holder of drinks
Removal and installation of facing of the lever of the parking brake
Removal and installation of a cover of the lever of switching of transfers/selector
Removal and installation of an ashtray
Removal and installation of the central armrest
Removal and installation of an internal mirror
Removal and installation of a cover on a control panel
Removal and installation of a pocket from the driver
Removal and installation of a ware box
Removal and installation of an antisolar peak
Removal and installation of facing are permanent And
Removal and installation of the top facing of a rack In
Removal and installation of the lower facing of a rack In
Removal and installation of a forward overlay of a threshold
Removal and installation of facings (Sedan)
Removal and installation of facings (Station wagon)
Removal and installation of a forward seat
Removal and installation of a back seat
Removal and installation of a forward seat belt
Removal and installation of a back seat belt
+ Onboard electric equipment
|
Removal and installation of facings (Sedan) Rack With
Removal
|
|
|
|
- To exclude operation a head safety cushion, switch off ignition and disconnect at first the negative (-), and then positive battery cables. Instructions are provided in the Section Replacement of the Battery.
- Remove the closing roof level, see below.
|
- Turn out screws (2).
|
|
- Remove lateral pillows of a back seat, address to the Section Removal and installation of a back seat.
- Take out a clip (3) under a lateral pillow.
- Disconnect the lateral shelf and raise it, address to appropriate section.
- Disconnect facing of a rack C (1) at a spring clip (4) and remove it.
|
|
Installation
|
|
- Raise the shelf and insert facing of a rack With into grooves on the shelf.
- Further installation is carried out in sequence, the return to removal. Thus replace the self-stopped screws (2) with the new.
|
|
During connection of the battery in salon there should not be people. |
- Remove an insulating tape from the negative plug of the battery, attach at first positive (+), and then a negative cable (-) to the battery.
|
|
Rack of D
Removal
|
|
|
|
- To exclude operation a head safety cushion, switch off ignition and disconnect at first the negative (-), and then positive battery cables. Instructions are provided in the Section Replacement of the Battery.
- Remove facing of a rack of D, address to appropriate section.
|
- Press down the handle (5) and cast away a cover of the screw (4) down. For this purpose enter (7) thin wire into a groove and open a cover.
|
|
- Turn out screws (6).
- Turn out the screw (3) and disconnect behind facing of a rack And, address to appropriate section.
- Extend facing (1) under facing of a rack of Century.
- Disconnect facing of a rack of D (1) at spring clips (2) and extend from the shelf.
|
|
Installation
|
|
- Enter into the shelf facing behind a rack of D.
- Insert a hook (7) in vents at facing of a rack of Page.
- Fix facing of a rack of D at spring clips (2).
- Insert forward facing under facing of a rack of Century.
- Check that the clip and a hook of the adapter of a safety cushion were reliably fixed.
- Screw the screw (3) and fix facing behind a rack And.
- Fix the handle the new self-stopped screws (6). Put into place a screw cover.
- Put a door sealant over facing.
- Establish into place a roof lock level, see below.
|
|
During connection of the battery in salon there should not be people. |
- Remove an insulating tape from the negative plug of the battery, attach at first positive (+), and then a negative cable (-) to the battery.
|
|
The closing roof level
Removal
|
|
- Disconnect the closing level of a roof (1) at spring clips (2) of grooves (3) and remove.
|
|
|
Installation
|
|
- Installation is carried out in sequence, the return to removal.
|
|
Back entrance level
Removal
Installation
|
|
- Installation is carried out in sequence, the return to removal.
|
|
Shelf
Removal
|
|
- Depending on the equipment: Cast away a back of a back seat or remove, address to the Section Removal and installation of a back seat.
- Disconnect from the shelf facing of a rack With at the left and on the right.
- Remove the left and right lateral pillows of a back seat, address to the Section Removal and installation of a back seat.
- Not leaning back back seat: Disconnect below the central seat belt.
|
- Remove from the shelf by means of a plastic wedge a lattice of a loudspeaker (3).
|
|
- Depending on the equipment turn out 3 or 4 screws (4).
- Turn out from below 3 screws of fastening of solar blinds in a luggage carrier and extend a curtain forward.
- Pull the shelf (1) (shooter) forward, disconnect at an edge (2) and take out upward.
|
|
Installation
|
|
- Installation is carried out in sequence, the return to removal.
|
|
Lateral facing of a luggage carrier
Removal
|
|
- Open a luggage carrier and take out a floor cover.
- Remove facing of overlapping of a back.
- Remove a back of a back seat, address to the Section Removal and installation of a back seat.
- Turn out bolts of fastening of eyes of a luggage carrier.
- Disconnect lateral facing at four spring clips above and behind and remove up. If it is necessary, previously open a sidewall cover in facing.
|
|
Installation
|
|
- Installation is carried out in sequence, the return to removal. Thus put a sealant of a door over facing.
|
|
Overlapping of a back
Removal
|
|
- Open a luggage carrier and take out a floor cover.
|
- Turn off 2 nuts (2), if necessary, take out a spare wheel.
|
|
- Disunite the luggage carrier lighting lamp socket.
- Disconnect facing of overlapping of a back (1) in four spring clips (3) and remove overlapping.
|
|
Installation
|
|
- Installation is carried out in sequence, the return to removal.
|
|
|
|