Audi A4, S4

since 2000 release

Repair and operation of the car



Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   + External equipment
   - Equipment of salon
      Remarks on work with the equipment of salon and a security measure
      Removal and installation of spring clips
      Removal and installation of the central console
      Removal and installation of the holder of drinks
      Removal and installation of facing of the lever of the parking brake
      Removal and installation of a cover of the lever of switching of transfers/selector
      Removal and installation of an ashtray
      Removal and installation of the central armrest
      Removal and installation of an internal mirror
      Removal and installation of a cover on a control panel
      Removal and installation of a pocket from the driver
      Removal and installation of a ware box
      Removal and installation of an antisolar peak
      Removal and installation of facing are permanent And
      Removal and installation of the top facing of a rack In
      Removal and installation of the lower facing of a rack In
      Removal and installation of a forward overlay of a threshold
      Removal and installation of facings (Sedan)
      Removal and installation of facings (Station wagon)
      Removal and installation of a forward seat
      Removal and installation of a back seat
      Removal and installation of a forward seat belt
      Removal and installation of a back seat belt
+ Onboard electric equipment






Removal and installation of the central console

1 — the Central console
2 — the Overlay of switching
3 — the Cover
4 — Screws
5 — the Cover under the lever of the parking brake
6 — the Connecting element

7 — Screws
8 — Screws
9 — Screws
10 — Screws
11 — the Nut, 26nm
12 — Nuts, 26nm

Removal

 PERFORMANCE ORDER

  1. Disconnect a negative cable (-) of the battery.

Observe indications of the Section Replacement of the Battery.

  1. Tighten the parking brake.
  2. Remove facing of the lever of the parking brake, address to the Section Removal and installation of facing of the lever of the parking brake.
  3. AT: Move the selector back.
  4. Uncover the lever of switching and remove the lever.
  5. Remove a lobby and a back ashtray, address to the Section Removal and installation of an ashtray.
  6. Remove the central armrest if it is established, address to the Section Removal and installation of the central armrest.
  7. Remove the radio receiver, address to the Section Removal and installation of the radio receiver / the navigation device / CD changer.
  8. Remove the control panel the heater/conditioner, address to the Section Removal and installation of the control unit of the heater/conditioner.
  9. Disconnect an overlay of switching (2) from the central console, address to the Section Removal and installation of the holder of drinks.
  10. Take out from the central console the right and left covers (3) and turn out fastening screws around an arrangement of feet.
  11. Take out by means of a plastic wedge a cover (5) of the central console under the lever of the parking brake.
  12. Depending on model disunite the socket of the lighter or the control unit of navigation.
  13. Turn out 2 screws of fastening (7) at a connecting element (6) and take out a connecting element.
  14. Turn out 2 screws (8) under an ashtray.
  15. Turn out 4 screws (9), and also 2 screws (10) of fastening of the central console (1).
  16. The car with the central armrest: Turn off a nut (11).
  17. Turn off 2 nuts (12).
  18. Pull the central console (1) back and remove from a floor.

The central console separates hardly.

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence, the return to removal. Thus nuts (11) and (12) are tightened by the moment 26nm.
  2. Attach a negative cable (-) of the battery.

Observe indications of the Section Replacement of the Battery.