Audi A4, S4

since 2000 release

Repair and operation of the car


Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   + External equipment
   - Equipment of salon
      Remarks on work with the equipment of salon and a security measure
      Removal and installation of spring clips
      Removal and installation of the central console
      Removal and installation of the holder of drinks
      Removal and installation of facing of the lever of the parking brake
      Removal and installation of a cover of the lever of switching of transfers/selector
      Removal and installation of an ashtray
      Removal and installation of the central armrest
      Removal and installation of an internal mirror
      Removal and installation of a cover on a control panel
      Removal and installation of a pocket from the driver
      Removal and installation of a ware box
      Removal and installation of an antisolar peak
      Removal and installation of facing are permanent And
      Removal and installation of the top facing of a rack In
      Removal and installation of the lower facing of a rack In
      Removal and installation of a forward overlay of a threshold
      Removal and installation of facings (Sedan)
      Removal and installation of facings (Station wagon)
      Removal and installation of a forward seat
      Removal and installation of a back seat
      Removal and installation of a forward seat belt
      Removal and installation of a back seat belt
+ Onboard electric equipment





Removal and installation of a cover of the lever of switching of transfers/selector

Manual check point

Removal

 PERFORMANCE ORDER

  1. Open an ashtray. Strongly pull a cover of the lever of switching (2) together with a cover (6) up, having disconnected from four clips.
  1. Remove a cover (6) up. Turn counterclockwise a nut (5) and remove the handle (4) from the lever.

Depending on model instead of a nut there can be a collar. (1) – selector cover.

  1. Press levels and disconnect a cover from a frame (3).

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence, the return to removal. Thus put on a cover the lever of switching (arrow B) turn a nut (5) clockwise (arrow A).

Automatic transmission

Removal

 PERFORMANCE ORDER

  1. Install the selector in the situation "D".
  1. Turn the plug (1) counterclockwise and shift down to an emphasis.
  1. Carefully pull a stopper (2) of the handle (3) so that the collar of a cable could be advanced through a gap between a stopper and the handle.

Do not extend a stopper far since otherwise it is possible to damage the selector.

  1. Close a collar round a clamp (shooter), tighten it and hold in such situation.
  2. Remove the handle (3) from the selector up.
  3. Open a forward ashtray and disconnect a cover.
  1. Release clips (2) and take out an overlay of the selector (1) of the central console up.
  1. Disunite the socket from a slip.

For removal of the Tiptronic switch press inside stoppers (2), disconnect a slip from the lower part and take out the switch from a slip.

  1. Disconnect strong breakthrough a cover of the selector (1) of the holder of a clip and pull up.

Installation

 PERFORMANCE ORDER

  1. Install the selector in the situation "D", establish a cover of the selector and record it.
  2. Join the socket, establish and record an overlay of the selector and a cover.
  3. Establish into place an ashtray cover.
  4. Install the handle on the selector and fix it.

The clamp thus has to be extended from the handle as it is described at removal, and is recorded by a cable collar. The clamp has to show towards the driver to the left.

  1. Remove a collar of a cable and press a clamp into the handle.
  2. Shift the plug on the selector up, turn clockwise and record.