Audi A4, S4

since 2000 release

Repair and operation of the car



Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water-collecting compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and installation/adjustment of a cowl
      Removal and installation of a cable of the drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and installation of a door
      Adjustment of a door
      Removal and installation of a frame of a window of a forward door
      Removal and installation of a window regulator
      Removal and installation of the electric motor of the drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and adjustment of a trunk lid
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Station wagon)
      Removal and installation of a door of a back (Station wagon)
      Removal and installation of the lock of a door of a back (Station wagon)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of screenwash
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + Equipment of salon
+ Onboard electric equipment






Removal and installation of a jet of windscreen washer of a windshield

Removal

 PERFORMANCE ORDER

  1. Open a cowl.

Jets of windscreen washer are established from the lower party of a cowl.

  1. By means of a plastic wedge, for example, allocate for HAZET 1965-20 the jet basis from a cowl.
  1. Remove a water hose from a jet.
  1. If necessary, disunite the socket of heating of a jet.

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence, the return to removal.
  2. Thus the water hose has to be recorded distinctly on a jet of washing of a windshield.
  3. Close a cowl and check operability of jets, if necessary, adjust.

Adjustment

 PERFORMANCE ORDER

  1. The direction of a stream of jets can be adjusted by means of the special tool 3125A or HAZET 4850-1. For this purpose insert a mandrel into a jet and apply a tag on glass.

Do not apply a needle since in this case it is possible to damage water channels of jets as a mandrel.

  1. Mark with a felt-tip pen on a windshield of 4 points to which the water stream has to get.

    and — from 250 to 275 mm (a cabriolet: 340 mm)
    b — from 465 to 490 mm (a cabriolet: 500 mm)
    with — from 270 to 415 mm (a cabriolet: 450 mm)
    d — from 140 to 225 mm (a cabriolet: 280 mm)

The specified adjusting sizes are established from an external edge of glass and represent anticipatory values for the moving car, i.e. in a motionless state jets give the stream which is a little displaced upward.

  1. If the stream is not regulated or is uneven, the jet needs to be replaced.
  1. If it is necessary, remove a jet for its cleaning and blow compressed air via the union for a hose.

Do not blow a jet against the direction of liquid.