Audi A4, S4

since 2000 release

Repair and operation of the car



Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Diagnostics of malfunctions of onboard electric equipment - the general information
   Rassoyedineniye of sockets
   Check of the electric motor of a screen wiper
   Check of the warmed back glass
   Check of stoplights
   Removal and installation of a sound signal
   Removal and installation of sensors of a parking
   Replacement of the battery of a remote control of the ignition key
   Relay and safety locks
   Replacement of glow lamps of devices of external lighting
   Removal and installation of headlights
   Removal and installation of the lateral repeater of turns
   Removal and installation of an additional stoplight
   Removal and installation of a back lamp
   Removal and installation of a lamp of illumination of registration plate
   Removal and installation of plafonds of internal lighting
   Removal and installation of a control panel
   Removal and installation of the understeering switch
   Removal and installation of switches of a forward door
   Removal and installation of the switch of light
   Removal and installation of the switch of a window regulator in a back door
   Removal and installation of the switch of a trunk lid
   Removal and installation of the switch of the parking brake
   Removal and installation of the switch of illumination of a ware box
   Removal and installation of switches of the central console
   Removal and installation of the radio receiver / navigation device / CD changer
   Removal and installation of loudspeakers
   Removal and installation of antennas
   Removal and installation of the tank of liquid of the windscreen washer/electric motor of the pump
   Removal and installation of the electric motor of screenwash
   Removal and installation of the electric motor on back glass (Station wagon)
   The uniform lock - the general information
   Removal and installation of a locking element of a cover of a fuel tank
   Digital tire of data of CAN
   + Schematic diagrams of electric equipment






Removal and installation of headlights

Headlight with a xenon lamp

Instruction: The headlight design with a galogenovy lamp corresponds to a headlight design with a xenon lamp. In a headlight with a galogenovy lamp there is no block of ignition only (2). The glow lamp of a passing beam (8), and also the electric motor of adjustment of range of light (11) are executed differently.
1 — the Screw
2 — the Block of ignition of a xenon lamp
3 — a headlight Frame
4 — the headlight Case
5 — Two elements of ventilation
6 — the Lamp of a passing beam
7 — the Cover, a reverse side of a passing beam

8 — the Xenon lamp of a passing beam
9 — the Cover, a reverse side of a driving beam
10 — the Glow lamp of a driving beam
11 — the Electric motor of adjustment of range of light
12 — the Glow lamp of a parking light
13 — the Sealing ring
14 — the Screw, 6nm
15 — the Persistent screw, for installation of a headlight has to adjoin to the forward panel

Removal

Be careful when replacing xenon lamps in headlights. Danger of traumatizing owing to a high voltage! Just in case switch off a headlight and disconnect the battery. After that quickly switch on and off the headlight switch to remove residual stress. For reasons of safety carry footwear with rubber soles.

 PERFORMANCE ORDER

  1. Disconnect a negative cable (-) of the battery.

Observe indications of the Section Replacement of the Battery.

  1. Take out the top left or right cover of the engine if it is established.
  2. Right headlight: Disconnect an air duct between the forward panel and the air filter, address to the Section Installation of the Forward Panel in situation for maintenance.
  3. Protect the area under a headlight for protection against damages of a paint and varnish covering an adhesive tape.
  1. Turn out screws (1) and (5).
  1. Unscrew screws (2) and (4) on some turns, without turning out them. (6) – persistent screw.
  2. Disconnect a cable and disunite the socket (3).
  3. Take out a headlight forward.

Installation

 PERFORMANCE ORDER

  1. Insert a headlight against the stop. Thus watch that two ventilating elements (5) on the right and at the left from the lower party of a headlight were established into place, address to an illustration the Headlight with a xenon lamp.
  2. If it is necessary, expose a headlight with the persistent screw (6) so that the uniform gap in relation to adjacent details of a body remained. Thus especially watch a prileganiye site to a wing.
  3. Tighten screws (1, 2, 4 and 5).
  4. Further installation is carried out in sequence, the return to removal.
  5. Adjust the provision of headlights as soon as possible on HUNDRED.

Adjustment

 PERFORMANCE ORDER

  1. Situation on height is regulated by screws (1 and 2), situation on the horizon the screw (2).

The correct provision of headlights can be adjusted only with use of special devices on HUNDRED.

Fog lights

Removal

 PERFORMANCE ORDER

  1. Remove an air admission lattice from a bumper, address to the Section Removal and installation of a front bumper.
  1. Turn out screws (arrows on an accompanying illustration), disconnect a headlight at inside of a bumper and take out it.
  1. Disunite the socket (1) headlight.

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence, the return to removal. Thus watch that the directing pins entered openings.

Replacement of glow lamps

 PERFORMANCE ORDER

  1. Turn a lamp with the boss (2) counterclockwise (shooter) and take out from the headlight case.