Audi A4, S4

since 2000 release

Repair and operation of the car

Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   + External equipment
   - Equipment of salon
      Remarks on work with the equipment of salon and a security measure
      Removal and installation of spring clips
      Removal and installation of the central console
      Removal and installation of the holder of drinks
      Removal and installation of facing of the lever of the parking brake
      Removal and installation of a cover of the lever of switching of transfers/selector
      Removal and installation of an ashtray
      Removal and installation of the central armrest
      Removal and installation of an internal mirror
      Removal and installation of a cover on a control panel
      Removal and installation of a pocket from the driver
      Removal and installation of a ware box
      Removal and installation of an antisolar peak
      Removal and installation of facing are permanent And
      Removal and installation of the top facing of a rack In
      Removal and installation of the lower facing of a rack In
      Removal and installation of a forward overlay of a threshold
      Removal and installation of facings (Sedan)
      Removal and installation of facings (Station wagon)
      Removal and installation of a forward seat
      Removal and installation of a back seat
      Removal and installation of a forward seat belt
      Removal and installation of a back seat belt
+ Onboard electric equipment

Removal and installation of a forward seat



Removal of a forward seat with a lateral safety cushion requires the AUDI VAS 6036 adapter.

  1. Seat with adjustment of height: Lift a seat.
  1. Pull upward a cover (2) over a tip (1) belt at a seat and remove.
  1. Press a tip of a belt (1) (arrow) down and disconnect from a seat. Extend a seat belt from directing a belt at a seat.
  1. Shift a forward seat (4) forward.
  1. Extend 4 clips (2) and remove back safety covers (1).
  2. Shift a forward seat back, extend 2 clips and remove forward covers of the directing.
  3. Turn out on 2 screws (3) behind and in front.
  4. To exclude operation a head safety cushion, switch off ignition and disconnect at first the negative (-), and then positive battery cables. Instructions are provided in the Section Replacement of the Battery.
  1. Cast away a forward seat (4) back and uncover upward (5) boxes for plugs.

Before undocking of the socket of a lateral safety cushion remove an electrostatic charge for what quickly concern the lock of a door or a body. The adapter of a safety cushion has to remain attached until the seat is not again established. Surely observe security measures at the address with a safety cushion, address to the Section General information and security measures.

  1. Press a pad at the plug and disunite the socket of a lateral safety cushion (orange color) (6).
  2. Disunite the food giving socket (red color) (7), heating of a seat (8) (green color) and a seat belt (black color) (9) if they are available.
  3. Attach the plug lateral a safety cushion (orange color) (6) to VAS 6036 safety cushion adapter.

The adapter provides additional protection against an electrostatic charge.

  1. If it is possible, attach other end of the adapter of a safety cushion to the food giving plug (red color) (7).
  2. Take out a forward seat.



  1. Installation is carried out in sequence, the return to removal. Thus fix a forward seat the moment 50nm.

During connection of the battery in salon there should not be people.

  1. Remove the isolating tape from a negative pole of the battery, attach at first positive (+), and then a negative cable (-) to the battery.

Observe indications of the Section Replacement of the Battery.

  1. If after ignition inclusion the safety cushion signaling device on a control panel does not die away, it is necessary to consider information from memory of malfunctions on HUNDRED.