Audi A4, S4

since 2000 release

Repair and operation of the car



Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water-collecting compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and installation/adjustment of a cowl
      Removal and installation of a cable of the drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and installation of a door
      Adjustment of a door
      Removal and installation of a frame of a window of a forward door
      Removal and installation of a window regulator
      Removal and installation of the electric motor of the drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and adjustment of a trunk lid
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Station wagon)
      Removal and installation of a door of a back (Station wagon)
      Removal and installation of the lock of a door of a back (Station wagon)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of screenwash
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + Equipment of salon
+ Onboard electric equipment






Replacement of elastic bands of brushes of a screen wiper

Replacement needs to be made at deterioration of purification of glass. Thus it is possible to replace only elastic bands, or complete with brush holders. If only elastic bands are replaced, it is necessary to check, whether has deformations the brush holder.

Removal

 PERFORMANCE ORDER

  1. Raise the lever and hold a brush perpendicularly to the lever.
  1. Press a spring clip in the direction of an arrow and put forward a brush from a hook on the lever down. Unhook a brush of the lever.
  1. Squeeze flat-nose pliers on the closed party of a brush both steel tires and take out them sideways from the top bracket. Further extend rubber together with directing from the brush bracket rest.

Installation

 PERFORMANCE ORDER

  1. Insert a new elastic band without tires into the lower brackets of a brush.
  1. Enter both tires into the first flute of a brush so that grooves of tires showed towards an elastic band and record in flute pads.
  1. Squeeze both steel tires and a brush of a passatizhama and insert into the top bracket so that bracket pads from both parties entered grooves (the shooter on an accompanying illustration) brushes.
  1. Insert a brush (2) into the lever (1). Thus the brush of the left lever has to connect to a collar, and the directing pad has to enter a brush.
  1. Press fixings the button and fix a brush.
  1. Cast away a brush back. Watch that the brush elastic band on all length adjoined to glass, if necessary, carefully turn in the holder.