Audi A4, S4

since 2000 release

Repair and operation of the car



Audi A4, S4
+ Introduction
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures when carrying out body works
   Cleaning and leaving
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   - External equipment
      Installation of the forward panel in situation for maintenance
      Removal and installation of a cover of a water-collecting compartment
      Removal and installation of a front bumper
      Removal and installation of a loker of a back wing
      Removal and installation of a loker of a forward wing
      Removal and installation of a forward wing
      Removal and installation of a rear bumper
      Removal and installation/adjustment of a cowl
      Removal and installation of a cable of the drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and installation of a door
      Adjustment of a door
      Removal and installation of a frame of a window of a forward door
      Removal and installation of a window regulator
      Removal and installation of the electric motor of the drive of a window regulator
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a trunk lid
      Removal, installation and adjustment of a trunk lid
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Station wagon)
      Removal and installation of a door of a back (Station wagon)
      Removal and installation of the lock of a door of a back (Station wagon)
      Removal and installation of an external mirror
      Removal and installation of moldings
      Removal, installation and check of the movable panel of a roof
      Removal and installation of an overlay of the movable panel of a roof
      Check and adjustment of a starting position of the movable panel of a roof
      Removal and installation of a sealant of the movable panel
      Replacement of elastic bands of brushes of a screen wiper
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of screenwash
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets of a faroomyvatel
      Adjustment of levers of a screen wiper
   + Equipment of salon
+ Onboard electric equipment






Removal and installation of the lock of a door

Removal

 PERFORMANCE ORDER

  1. Disconnect a negative cable (-) of the battery.

Observe indications of the Section Replacement of the Battery.

  1. Remove a door upholstery, address to appropriate section.
  2. Remove a door frame with a window regulator from a door, address to the Sections Removal and installation of a frame of a window of a forward door and Removal and installation of a window regulator.
  3. Disunite the door lock socket.
  1. At installation of the old lock: Disconnect a driving bar (3) at the handle of a door (1) of the holder of a clip (2).
  1. At installation of the new lock of a door: Displace the plug (4) down and take out a driving bar (3). (5) – a lock pin, (6) – tear up the lock.
  1. Turn out 2 bolts (1) and take out the lock (3) from a door down. (2) – lining.
  1. Disconnect a cable (5) drives of a door at the lock and at the uncoupling lever (4).

Installation

 PERFORMANCE ORDER

  1. Connect a cable (5) drives of a door to the uncoupling lever (4), turn on 90 ° (shooter) and connect to the lock.
  2. Insert the lock into a door and fix it the moment 20nm.
  1. At installation of the new lock: Insert a bar of the drive (3) into the plug (4). For fixing displace the plug up. Take out a lock pin (5) of the lock (6).
  1. At installation of the old lock: Connect a driving bar to the door handle, address to the Section Removal and installation of the handle of a door.
  2. Join the door lock socket.
  3. Put a door frame with a window regulator on a door, address to the Section Removal and installation of the electric motor of the drive of a window regulator.
  4. Establish a door upholstery, address to appropriate section.
  5. Attach a negative cable (-) of the battery.

Observe indications of the Section Replacement of the Battery.